声明：本产品严禁用于军事及生命安全相关场景，违规使用责任由使用人自负
| 主要参数 | 最小值 | 典型值 | 最大值 | 备注 | |
| 工作电压 VCHG（V） | 4 | 5 | 5.5 | 超过6.5V永久烧毁模块 | |
| 工作电压 VBAT（V） | 3 | 3.7 | 4.3 | 超过4.3V永久烧毁模块 | |
| 通信电平（V） | 1.8 | 3.3 | 3.6 | 电平由VDD_PADS1电平决定 | |
| 工作温度（℃） | -40 | 20 | 85 | 工业级设计 | |
| 工作频段（MHz） | 2402 | — | 2480 | 支持蓝牙协议标准频段 | |
| 功耗 | 未连接电流（mA） | — | 6.5 | — | 蓝牙处于可被发现状态 |
| 连接并播放音频电流（mA） | — | 6 | — | 蓝牙已连接但是未播放音乐 | |
| 关机电流（uA） | — | 21 | — | 仅VBAT供电时 | |
| 最大发射功率（dBm） | — | 8 | — | — | |
| 接收灵敏度（dBm） | — | -97 | — | Basic Rate | |
| 主要参数 | 描述 | 备注 |
| 参考距离 | 200m | 晴朗空旷环境，与手机互通 |
| 封装方式 | 贴片式 | — |
| 输出接口 | DAC/I2S/SPDIF | DAC/I2S/SPDIF输出切换 |
| 通信接口 | UART | — |
| 接口方式 | 邮票孔 | 间距1.00mm |
| 外形尺寸 | 13*18mm | ±0.2mm |
| 天线接口 | 邮票孔 | 等效阻抗约50Ω |
| 重量 | 1.0g | ±0.1g |
| 工作温度 | -40~+85℃ | 工业级设计 |
| 引脚序号 | 引脚名称 | 电源 | 引脚方向 | 引脚说明 |
| 1 | GND | — | GND | 地 |
| 2 | PIO21 | VDD_PADS | I/O | 可编程I/O口21，IO21拉高时，选择SPDIF输出，其它功能：PCM_DOUT2 |
| 3 | PIO20 | I/O | 功放使能引脚，可编程I/O口20 | |
| 4 | PIO19 | I/O | 可编程I/O口19，其它功能：PCM_DIN0 | |
| 5 | PCM_DOUT0 | I/O | 可编程I/O口18，接I2S DIN 或 SPDIF OUT | |
| 6 | PCM_SYNC | I/O | 可编程I/O口17，接I2S_LRCK | |
| 7 | PCM_CLK | I/O | 可编程I/O口16，接I2S_BCK | |
| 8 | PCM_MCLK | I/O | 可编程I/O口15，接I2S_MCK | |
| 9 | USB_DN | — | I/O | USB 数据负端 |
| 10 | USB_DP | — | I/O | USB 数据正端 |
| 11 | SYS_CTRL | VBAT | I | 高电平保持6秒后，再切换至低电平，开/关机，自动进入配对模式 |
| 12 | VBAT | VBAT | I | 电池接口,电池电压输入，3.0~4.3V |
| 13 | CHG_EXT | VCHG | I | 外部充电控制,外部充电晶体管电流控制 |
| 14 | VCHG | VCHG | I | 充电接口,电池充电输入，4.0V~5.5V |
| 15 | LED3 | — | I/O | 模拟/数字输入、开漏LED输出 |
| 16 | LED2 | — | I/O | 模拟/数字输入、开漏LED输出，配对状态下闪烁 |
| 17 | GND | — | GND | 地 |
| 18 | LED1 | — | I/O | 模拟/数字输入、开漏LED输出 |
| 19 | LED0 | — | I/O | 模拟/数字输入、开漏LED输出 |
| 20 | P107 | VDD_PADS | I/O | 可编程I/O口7，UART_RX |
| 21 | P104 | I/O | 按键PIO[4]，短按播放暂停 | |
| 22 | P103 | I/O | 按键PIO[3] 短按音量加，长按一直加，双击下一曲 | |
| 23 | P106 | I/O | 可编程I/O口6，UART_TX | |
| 24 | P105 | I/O | 按键PIO[5] 短按回连，长按3秒断开连接，6秒进配对，8秒清空列表 | |
| 25 | P108 | I/O | 可编程I/O口8，IO8拉高时，选择DAC输出 | |
| 26 | PIO2 | I/O | 按键PIO[2]，短按音量减，长按一直减，双击上一曲 | |
| 27 | RESET#/PIO1 | I/O | 按键PIO[1]模组复位控制按键，按下复位 | |
| 28 | GND | — | GND | 地 |
| 29 | VDD_PADS | — | PWR | PIO电源输入,1.8 V/3.3V PIO电源 |
| 30 | 1V8_SMPS | — | PWR_OUT | 电源输出,1.8V电源输出 |
| 31 | SPKR_N | — | O | 扬声器差分输出右声道负极 |
| 32 | SPKR_P | — | O | 扬声器差分输出右声道正极 |
| 33 | SPKL_N | — | O | 扬声器差分输出左声道负极 |
| 34 | SPKL_P | — | O | 扬声器差分输出左声道正极 |
| 35 | MIC_BIAS | — | O | 模拟输出,麦克偏置输出 |
| 36 | MIC1_N | — | I | 模拟输入,麦克风差分输入1负极 |
| 37 | MIC1_P | — | I | 模拟输入,麦克风差分输入1正极 |
| 38 | MIC2_N | — | I | 模拟输入,麦克风差分输入2负极 |
| 39 | MIC2_P | — | I | 模拟输入,麦克风差分输入2正极 |
| 40 | MIC3_N | — | I | 模拟输入,麦克风差分输入3负极 |
| 41 | MIC3_P | — | I | 模拟输入,麦克风差分输入3正极 |
| 42 | MIC4_N | — | I | 模拟输入,麦克风差分输入4负极 |
| 43 | MIC4_P | — | I | 模拟输入,麦克风差分输入4正极 |
| 44 | GND | — | GND | 地 |
| 45 | GND | — | GND | 地 |
| 46 | RF_PORT | — | O | 外接天线 |
| 47 | GND | — | GND | 地 |
| 48 | PIO39 | VDD_PADS | I/O | 可编程I/O口39，其它功能：QSPI2_IO3 |
| 49 | PIO38 | VDD_PADS | I/O | 可编程I/O口38，其它功能：QSPI2_CS# |
| 50 | PIO37 | VDD_PADS | I/O | 可编程I/O口37，其它功能：QSPI2_IO1 |
| 51 | PIO36 | VDD_PADS | I/O | 可编程I/O口36，IO36拉高时,USB输入,拉低时AUX输入，其它功能：QSPI2_IO2 |
| 52 | PIO35 | VDD_PADS | I/O | 可编程I/O口35，其它功能：QSPI2_CLK |
| 53 | PIO34 | VDD_PADS | I/O | 可编程I/O口34，其它功能：QSPI2_IO0 |
| 54 | PIO22 | VDD_PADS | I/O | 可编程I/O口22，其它功能：PCM_DIN1 |
| 产品说明书 |
【用户手册】EWM104-BT3095_UserManual_CN  |
| 开发测试 |
【3D文件】EWM104-BT3095  |
| 【封装文件】EWM104-BT3095 |
| 【推荐原理图】EWM104-BT3095 |
| 工具软件 |
| 【通信测试】串口调试助手_XCOM |
| 亿佰特简介 |
| 【企业简介】 |
| 批量采购/定制产品 |
| 【销售专线】：4000-330-990 7x24小时销售服务热线 |
| 【联系邮箱】：support@cdebyte.com |
| 技术咨询 |
| 【在线提交】：https://www.ebyte.com/apple-technology.html |
| 【联系邮箱】：support@cdebyte.com |
| 产品 型号 | 接口类型 | 芯片方案 | 工作频率 Hz | 发射功率 dBm | 通信距离 km | 通信协议 | 天线形式 | 产品尺寸 mm | 功能特点 | 技术 手册 | 样品 购买 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| EWM104-BT3095 | UART | QCC3095 | 2.4G | 8 | 0.2 | BLE 5.4 | 邮票孔 | 13*18 | DAC/I2S/SPDIF 输出接口、贴片式封装、高通蓝牙音频模块 | ||
| E104-BT56SX | UART | - | 2.4G | 8 | 0.2 | BLE 5.3 | IPEX3 | 10*10 | 串口转BLE蓝牙模块 | ||
| E104-BT56SP | UART | - | 2.4G | 8 | 0.15 | BLE 5.3 | 板载PCB天线 | 10*14.5 | 串口转BLE蓝牙模块 | ||
| E104-BT14SX | UART | - | 2.4G | 9 | 0.32 | BLE 5.4 | 贴片式 | 10*10 | 低功耗、IPEX-3天线、蓝牙转串口模块 | ||
| E104-BT14SP | UART | - | 2.4G | 9 | 0.2 | BLE 5.4 | 贴片式 | 10*14.5 | 低功耗、PCB板载天线、蓝牙转串口模块 | ||
| EWD104-BT58PA | - | - | 2.4G | 0~8 | 0.16 | BLE 5.3 | 内置天线 | 40*12 | 防水款、全国产化、低功耗iBeacon蓝牙信标 | ||
| EWD104-BT58P | - | - | 2.4G | 0~8 | 0.16 | BLE 5.3 | 内置天线 | 40*12 | 防水款、全国产化、低功耗iBeacon蓝牙信标 | ||
| EWD104-BT58THA | - | - | 2.4G | 0~8 | 0.16 | BLE 5.3 | 内置天线 | 40*12 | 常规款、全国产化、低功耗iBeacon蓝牙信标 | ||
| EWD104-BT58TH | - | - | 2.4G | 0~8 | 0.16 | BLE 5.3 | 内置天线 | 40*12 | 常规款、全国产化、低功耗iBeacon蓝牙信标 | ||
| EWD104-BT58 | - | - | 2.4G | 0~8 | 0.16 | BLE 5.3 | 内置天线 | 40*12 | 常规款、全国产化、低功耗iBeacon蓝牙信标 | ||
| EWM104-BT62SP | UART | - | 2.4G | 6 | 0.1 | BLE 5.3 | PCB | 13*19 | 符合蓝牙V5.3 BR+EDR+BLE规范的蓝牙音频收发模块 | ||
| EWM104-BT61SP | UART | - | 2.4G | 8 | 0.16 | BLE 5.4 | PCB | 14*22 | 双模蓝牙音频数传+广播发射收发模块 | ||
| EWM104-BT61SX | UART | - | 2.4G | 8 | 0.16 | BLE 5.4 | IPEX-1 | 14*16.8 | 双模蓝牙音频数传+广播发射收发模块 | ||
| EWM104-BT60SP3 | UART | - | 2.4G | 8 | 0.3 | BLE 5.2 | 邮票孔/PCB | 13*19 | 低成本无线音频+数传双模蓝牙从机模块 | ||
| EWM104-BT60SP2 | UART | - | 2.4G | 8 | 0.3 | BLE 5.2 | 邮票孔/PCB | 13*19 | 低成本无线音频+数传双模蓝牙从机模块 | ||
| E104-BT52X-V5.3 | UART | DA14535 | 2.4G | 3 | 0.25 | BLE 5.3 | IPEX-3 | 10*10 | 超小体积，高性能、主从一体 | ||
| E104-BT52-V5.3 | UART | DA14535 | 2.4G | 4 | 0.18 | BLE 5.3 | PCB | 14.5*10 | 低功耗，小体积，高性价比、主从一体 | ||
| E104-BT40X | UART | - | 2.4G | 3 | 0.04 | V4.2+V3.0 SPP | IPEX 3 | 16*13 | 低功耗，串口转双模蓝牙从机 | ||
| EWM104-BT41SP | UART | - | 2.4G | 8 | 0.1 | SPP+ BLE5.4 | PCB | 10*14.5 | 超低成本双模蓝牙从机模块 | ||
| EWM104-BT41SX | UART | - | 2.4G | 8 | 0.2 | SPP+ BLE5.4 | IPEX 3代 | 10*10 | 超低成本双模蓝牙从机模块 | ||
| EWM104-BT3040(I2S) | USB | QCC3040 | 2.4G | 9 | 0.22 | BLE 5.2 | 邮票孔 | 13*18 | I2S输出接口、贴片式封装、高通蓝牙音频模块 | ||
| EWM104-BT3040(DAC) | USB | QCC3040 | 2.4G | 9 | 0.22 | BLE 5.2 | 邮票孔 | 13*18 | DAC输出接口、贴片式封装、高通蓝牙音频模块 | ||
| EWM104-BT13SX | UART | - | 2.4G | 10 | 0.07 | BLE 5.0 | 贴片式 | 10*10 | 低功耗、小体积、3代IPEX天线接口、蓝牙接近开关模块 | ||
| EWM104-BT13SP | UART | - | 2.4G | 10 | 0.06 | BLE 5.0 | 贴片式 | 10*10 | 低功耗、小体积、PCB板载天线、蓝牙接近开关模块 | ||
| EWM104-BT5125(SPDIF) | USB | QCC5125 | 2.4G | 9 | 0.12 | BLE 5.1 | 邮票孔 | 13*18 | SPDIF输出接口、无线蓝牙音频模块 | ||
| EWM104-BT5125(I2S) | USB | QCC5125 | 2.4G | 9 | 0.12 | BLE 5.1 | 邮票孔 | 13*18 | I2S输出接口、无线蓝牙音频模块 | ||
| EWM104-BT5125(DAC) | USB | QCC5125 | 2.4G | 9 | 0.12 | BLE 5.1 | 邮票孔 | 13*18 | DAC输出接口、无线蓝牙音频模块 | ||
| EWD104-BT57(485) | RS485 | - | 2.4G | 20 | 0.56 | BLE 5.2 | SMA-K | 102*28*27 | 国产RS232/RS485转蓝牙无线适配器 | ||
| E104-BT52PX | UART | DA14531 | 2.4G | 20 | 0.5 | BLE 5.0 | IPEX 3代 | 16*10 | 低功耗，小体积，高性价比 | ||
| EWM104-BT57UP | USB | - | 2.4G | 23 | 0.22 | BLE 5.2 | PCB | 60*18*8.5 | 蓝牙转USB适配器，低功耗、主从一体、虚拟串口模块 | ||
| EWM104-BT57U | USB | - | 2.4G | 4.5 | 0.1 | BLE 5.2 | PCB | 18.5*14.5*6.0 | USB转蓝牙适配器，小体积、主从一体、虚拟串口模块 | ||
| EWM104-BT09SX | UART | TLSR8208BER | 2.4G | 11.5 | 0.2 | BLE 5.0 | 贴片式 | 10*10 | 低功耗小体积，蓝牙从机模块 | ||
| EWM104-BT09SP | UART | TLSR8208BER | 2.4G | 11.5 | 0.12 | BLE 5.0 | 贴片式 | 10*14.5 | 低功耗，蓝牙转串口从机模块 | ||
| E104-BT5032B | UART | nRF52832 | 2.4G | 20 | 0.5 | BLE 5.0 | 陶瓷天线 | 11.6*20 | 低功耗，透明传输，主从一体 | ||
| E104-BT09 | UART | TLSR8208BER | 2.4G | 11.5 | 0.15 | BLE 5.0 | 贴片式 | 13*19 | 低功耗，从机模块 | ||
| E104-BT08 | UART | - | 2.4G | 8 | 0.06 | BLE 5.1 | 贴片式 | 10*10 | 低功耗，主从一体 | ||
| E104-BT07 | UART | - | 2.4G | 8 | 0.13 | BLE 5.1 | 贴片式 | 21.9*14.6 | 低功耗，主从一体 | ||
| E104-BT53C3 | UART | EFR32BG22 | 2.4G | 6 | 0.17 | BLE 5.2 | PCB | 23*16 | 车规级耐高温、串口转BLE蓝牙模块 | ||
| E104-BT55SP | UART | CC2340R5 | 2.4G | 8 | 0.17 | BLE 5.3 | 板载PCB天线 | 10*14.5 | 低功耗，小体积 | ||
| E104-BT52X | UART | DA14531 | 2.4G | 0 | 0.13 | BLE 5.0 | IPEX 3代 | 10*10 | 低功耗，小体积，高性价比 | ||
| E104-BT11G-PCB | UART | EFR32MG21 | 2.4G | 20 | 0.2 | BLE Mesh | PCB | 19*13 | SigMesh自组网 | ||
| E104-BT5032U | USB | nRF52832 | 2.4G | 3 | 0.08 | BLE 4.2/BLE 5.0 | PCB | 59 * 18 | 蓝牙SoC方案，USB接口 | ||
| E104-BT53A3 | UART | EFR32BG22C224F512GM32 | 2.4G | 6 | 0.12 | BLE 5.2 | PCB | 13*19 | 低功耗，透明传输 | ||
| E104-BT12NSP-TB | USB | - | - | - | - | - | - | 46.5*26 | E104-BT12NSP模块测试板 | ||
| E104-BT12LSP-TB | USB | - | - | - | - | - | - | 46.5*26 | E104-BT12LSP模块测试板 | ||
| E104-BT12USP-TB | UART | TLSR8253F512 | 2.4G | 10 | 0.06 | - | PCB | 19*13 | SigMesh自组网 | ||
| E104-BT12LSP | UART | TLSR8253F512 | 2.4G | 10 | 0.06 | - | PCB | 19*13 | SigMesh自组网 | ||
| E104-BT12NSP | UART | TLSR8253F512 | 2.4G | 10 | 0.06 | - | PCB | 19*13 | SigMesh自组网 | ||
| E104-BT5040UA | USB | nRF52840 | 2.4G | 8 | 0.25 | BLE 4.2/BLE 5.0 | PCB | 59 * 18 | 蓝牙SoC方案，USB接口 | ||
| E104-BT5005A | UART | nRF52805 | 2.4G | 4 | 0.07 | BLE 5.0 | 陶瓷天线 | 9*9 | 超小体积封装，透明传输 | ||
| E104-BT5011A | UART | nRF52811 | 2.4G | 4 | 0.07 | BLE 5.1 | 陶瓷天线 | 11.5*16 | Long Range特性，透明传输 | ||
| E104-BT51A | UART | CC2640R2L | 2.4G | 5.5 | 0.05 | BLE 5.0 | 陶瓷天线 | 16*11.5 | 低功耗，透明传输 | ||
| E104-BT5040U | USB | nRF52840 | 2.4G | 8 | 0.25 | BLE 4.2/BLE 5.0 | PCB | 59 * 18 | 蓝牙SoC方案，USB接口 | ||
| E104-BT52 | UART | DA14531 | 2.4G | 0 | 0.09 | BLE 5.0 | 板载天线 | 14.5*10 | 低功耗，小体积，高性价比 | ||
| E104-BT53A1 | UART | EFR32 | 2.4G | 6 | 0.12 | BLE 5.2 | PCB | 13*19 | 低功耗，透明传输 | ||
| E104-BT40 | UART | - | 2.4G | 3 | 0.03 | V4.2+V3.0 SPP | PCB | 21*13 | 低功耗，串口转双模蓝牙从机 | ||
| E104-BT51 | UART | CC2640R2F | 2.4G | 5 | 0.75 | BLE 5.0 | PCB/IPX | 17.5*28.7 | 低功耗，透明传输 | ||
| E104-BT5032A | UART | nRF52832 | 2.4G | 4 | 0.06 | BLE 5.0 | 陶瓷天线 | 11.6 * 16 | 低功耗，透明传输 | ||
| E104-BT5010A | UART | nRF52810 | 2.4G | 4 | 0.055 | BLE 5.0 | 陶瓷天线 | 11.5*16 | 低功耗，透明传输 | ||
| E104-BT54S | UART | BLUENRG355MC | 2.4G | 8 | 0.3 | BLE 5.1 | IPEX，板载PCB天线 | 28*16*2.7 | STM意法半导体全新SoC蓝牙模块 | ||
| E104-BT05 | UART | - | 2.4G | 8 | 0.07 | BLE 5.0 | PCB | 10*14.5 | 低功耗，透明传输 | ||
| E104-2G4U04A | USB | CC2540 | 2.4G | 4 | 0.06 | BLE 4.0 | PCB | 59 * 18 | 蓝牙SoC方案，USB接口 | ||
| E104-BT02 | UART | DA14580 | 2.4G | 0 | 0.1 | BLE 4.2 | PCB | 14 * 22 | 透明连传，业界最低功耗 | ||
| E104-BT01 | I/O | CC2541 | 2.4G | 0 | 0.05 | BLE 5.0 | PCB | 14 * 22 | 超低功耗，高性价比 |
