[IC] : CC1352P
[Frequency] : 431~500MHz
[Power] : 20dBm/4.5dBm
[Distance] : 1.5km/0.12km
[Size] : 32*20mm
[Weight] : 2.8±0.1g
[Introduction] : Based on TI CC1352P chip, E79-400DM2005S is a dual-band ARM-based RF SoC Module
designed by Ebyte, with max transmitting power of 20dBm at SUB-1GHz and 5dBm at 2.4GHz.
The module integrates a high-performance wireless transceiver and a low temperature drift
industrial crystal oscillator.
Main Parameters | Value | Remarks | |
Min. | Max | ||
Input Voltage(V) | 0 | 3.8 | Permanent damage occurred when voltage is over 3.8V |
Blocking Power(dBm) | - | 10 | Low chance to be damaged for short-distance transceiving |
Working Temp.(℃) | -40 | +85 | Industrial Grade |
SUB-1GHz Parameters:
Main Parameters | Value | Remarks | |||
Min. | Typical | Max | |||
Working Voltage(V) | 2.1 | 3.3 | 3.8 | Voltage above 3.3V can guaranty Max TX power | |
Tx Electrical Level(V) | - | 3.3 | - | 5V TTL could cause permanent damage | |
Working Temp (℃) | -40 | - | +85 | Industrial Grade | |
Working Frequency (MHz) | 431 | - | 500 | Applicable for ISM channel | |
Power Consumption | TX Current(mA) | - | 75 | - | Instantaneous power |
RX Current(mA) | - | 6.5 | - | / | |
Sleeping Current(μA) | - | 2 | - | Software off | |
Max TX Power(dBm) | 19 | 20.0 | 20.5 | / | |
RX Sensitivity(dBm) | - | -122 | - | At 2.5 kbps air rate |
2.4G Parameters:
Main Parameters | Value | Remarks | |||
Min. | Typical | Max | |||
Working Voltage(V) | 1.8 | 3.3 | 3.8 | Voltage above 3.3V can guaranty Max TX power | |
Tx Electrical Level(V) | - | 3.3 | - | 5V TTL could cause permanent damage | |
Working Temp (℃) | -40 | - | +85 | Industrial Grade | |
Working Frequency (MHz) | 2360 | - | 2500 | Applicable for ISM channel | |
Power Consumption | TX Current(mA) | / | 10.5 | / | Instantaneous power |
RX Current(mA) | / | 7.5 | / | ||
Max TX Power(dBm) | 4 | 4.5 | 5 | / | |
RX Sensitivity(dBm) | / | -103 | / | BLE 5 Coding |
Parameters | Value | Remarks |
Reference Range | 1500m@SUB-1GHz | Conditions: Clear Sky, Antenna Gain 5dBi, Antenna Height 2.5m, Air rate 1kbps |
120m@2.4G | Conditions: Clear Sky, Antenna Gain 5dBi, Antenna Height 2.5m, Air rate 1Mbps | |
TCXO Frequency | 48MHz/32.768k | High rate at 48MHz/Low Rate at 32.768k |
Protocol | GFSK | / |
Encapsulation | SMD | / |
Interface Type | 1.27mm Stamp Hole | / |
IC Model | CC1352P1F3RGZ | / |
FLASH | 352KB | / |
RAM | 80KB | / |
Core | Arm ® Cortex ® -M4F | / |
Size | 32*20mm | / |
Antenna Interfaces | IPEX/Stamp Hole@sub-1G, PCB Antenna@2.4G | Equivalent Impedance is around 50Ω |
No. | Name | Direction | Function |
1 | GND | - | Ground wire, connected to the power reference ground |
2 | VCC | - | Power supply, range 2.5-3.7v (external ceramic filtercapacitor is recommended) |
3 | SETB | Input/output | Ground wire, connected to the power reference ground |
4 | DIO1 | Input/output | Multipurpose digital IO cannot be used as external GPIO |
5 | BUSY | Input/output | SPI busy indicator that cannot be used as an externalGPIO |
6 | I2C_SDA | Input/output | I2C SCL pins |
7 | I2C_SCL | Input/output | I2C SDApin |
8 | UART_CTS | Input/output | UART CTS pin |
9 | UART_RTS | Input/output | UART RTS pin |
10 | GND | - | Ground wire, connected to the power reference ground |
11 | ANT | - | Antenna interface, stamp hole (50 ohm characteristicimpedance) |
12 | GND | - | Ground wire, connected to the power reference ground |
13 | GND | - | Ground wire, connected to the power reference ground |
14 | GND | - | Ground wire, connected to the power reference ground |
15 | GND | - | Ground wire, connected to the power reference ground |
16 | XRES | Input | External reset pins |
17 | ADC_IN | Input | ADC input pin |
18 | AUX | Input/output | MCU GPIO |
19 | SETA | Input/output | MCU GPIO |
20 | UART_RX | Input/output | UART RX pin |
21 | UART_TX | Input/output | UART TX pin |
22 | SWD_DATA | Input/output | SWD Data pins |
23 | SWD_CLK | Input/output | SWD Clock pin |
24 | GND | - | Ground wire, connected to the power reference ground |
25 | SPI_MISO | Input/output | SPI MISO test point, internally connected, cannot be used as external SPI |
26 | SPI_NSS | Input/output | SPI NSS test point, internally connected,cannot be used as an external SPI |
27 | SPI_MOSI | Input/output | SPI MOSI test point, internally connected,cannot be used as an external SPI |
28 | SPI_SCK | Input/output | SPI SCK test point, internally connected,cannot be used as external SPI |
Order online |
【eBay】:https://www.ebay.com/usr/cdebyte |
【Aliexpress】:https://cdebyte.pt.aliexpress.com |
【Alibaba】:https://www.alibaba.com |
For batch order/customized product |
【Sales hotline】:+86-28-61399028 Ext.812 |
【E-mail】:service@cdebyte.com |
Technical support |
【Submit online】:http://www.ebyte.com/en/apple-technology.aspx |
【E-mail】:support@cdebyte.com |