[IC]：TLSR8258
[Frequency]：2.40~2.48GHz
[Power]：12dBm
[Distance]：200m
[Size]：11.5*22mm
[Introduction]：E180-Z5812SP is a ZigBee module based on TELINK TLSR8258 wireless SoC designed and produced by Ebyte, which is small size, low power consumption, high reliability and works in 2.4GHz frequency band. The chip has a 32-bit high-performance MCU up to 48mhz, with a maximum transmission power of 12dBm and a minimum sleep current of 2uA.
| Main parameter | Description | Remark |
Reference range | 200m | Between two points (ZigBee network supports multi hop routing function, and can extend therangeby adding routers) |
| weight | 0.9g | - |
| Protocol | Zigbee 3.0 | - |
| Package | SMD | - |
| Interface | 1.27mm | Stamp Hole |
| IC | TLSR8258F512ET32 | - |
| FLASH | 512KB | - |
| RAM | 64KB | - |
| Core chip | 32 bit MCU | - |
| Size | 11.5*22mm | - |
| Antenne | PCB | 50Ω |
| Main parameter | Min. | Typ. | Max. | Unit | Remark |
| Power supply | 1.9 | 3.3 | 3.6 | V | ≥3.3V can guarantee output power |
| Communication level | - | 3.3 | - | V | Risk of damage using 5V TTL |
| Working temperature | -40 | - | +85 | ℃ | Industrial |
| Working frequency band | 2405 | - | 2480 | MHz | Support ISM band |
| TX current | - | 24 | - | mA | Max 24mA at 12dbm |
| RX current | - | 9 | - | mA | - |
| Sleep current | - | 2.5 | - | μA | Periodic sleep current averages 2.5uA |
| Max output power | - | 12 | - | dBm | - |
| Air data rate | - | 250k | - | bps | - |
| Pin No. | Pin Name | Input/output | Functions |
| 1 | NC | - | Reserved, directly suspended |
| 2 | GND | - | Ground |
| 3 | NC | - | Reserved, suspended |
| 4 | PD3(WAKE) | Input | The WAKE The wake pin is mainly used to wake up the sleepingterminal. The default value is high level. When the pin is pulled down, the sleeping terminal device will wake up |
| 5 | PD7(TX) | Output | Serial transmission port TX |
| 6 | PA0(RX) | Input | Serial receiving port RX |
| 7 | NC | - | Reserved, suspended |
| 8 | NC | - | Reserved, suspended |
| 9 | PD4(MODE) | Input | Working mode switch pin, when pull down time is more than 500ms, switch working mode |
| 10 | PA1(BAUD_R) | Input | UART_ BAUD_ The reset pin is used to reset the baud rate of the device. The default value is high level. In any mode, if the pin is pulled down for more than 1000ms, thedefault baud rate will restore to 115200 |
| 11 | PB1(ACK) | Output | The ACK pin is used to indicate the status of the last user data transmission. The pin is pulled down before the transmission is started, and it is pulled up after the transmission is down |
| 12 | PC0(GPIO0) | Input/output | GPIO input/output port 0 |
| 13 | VCC | - | Power supply |
| 14 | GND | - | Ground |
| 15 | PB4(GPIO1) | Input/output | GPIO input/output port 1 |
| 16 | NC | - | Reserved, suspended |
| 17 | NC | - | Reserved, suspended |
| 18 | PB5(AUX) | Output | The AUX pin indicates the current working status of the device. When the pin is low, it indicates that the device is busy, and the high level indicates that the device is idle. |
| 19 | NC | - | Reserved, suspended |
| 20 | NC | - | Reserved, suspended |
| 21 | PB6(ADC1) | Input | ADC detection port 1 |
| 22 | PB7(ADC2) | Input | ADC detection port 2 |
| 23 | NC | - | Reserved, directly suspended |
| 24 | NC | - | Reserved, directly suspended |
| 25 | NC | - | Reserved, directly suspended |
| 26 | SWS | - | Reserved |
| 27 | PC2(PWM0) | Output | PWM output port 0 |
| 28 | PC3(PWM2) | Output | PWM output port 2 |
| 29 | PC4(PWM3) | Output | PWM output port 3 |
| 30 | PC1(LINK) | Output | The LINK pin indicates the current network status of the module, and the output high-level meter has been added to the network |
| 31 | NC | - | Reserved, suspended |
| 32 | PD2(PWM1) | Output | PWM output port 1 |
| 33 | NC | - | Reserved, suspended |
| 34 | NC | - | Reserved, suspended |
| 35 | NC | - | Reserved, suspended |
| 36 | GND | Input/output | Ground |
| 37 | nRESET | Input | Reset |
| Order online |
| 【eBay】：https://www.ebay.com |
| 【Aliexpress】：https://www.aliexpress.com |
| 【Aliexpress】：https://www.aliexpress.com |
| For batch order/customized product |
| 【Sales hotline】：+86-28-61399028 Ext.812 |
| 【E-mail】：service@cdebyte.com |
| Technical support |
| 【Submit online】：http://www.ebyte.com/en/apple-technology.aspx |
| 【E-mail】：support@cdebyte.com |
| Model | Interface | IC | Frequency Hz | Power dBm | Distance km | Air data rate | Package | Size (mm) | Feature | Manual | Sample |
|---|---|---|---|---|---|---|---|---|---|---|---|
| E180-Z8910SX | 1.27mm stamp hole | JN5189 | 2.4G | 11 | 0.5 | 250kbps | SMD | 11.5*18 | ZigBee 3.0 | ||
| E180-Z8910SP | 1.27mm stamp hole | JN5819 | 2.4G | 11 | 0.5 | 250kbps | SMD | 11.5*22.7 | ZigBee3.0 | ||
| E180-Z5812SP | I/O | TLSR8258 | 2.4G | 12 | 0.2 | 250kbps | SMD | 11.5*22 | ZigBee3.0 | ||
| E180-Z5812SX | I/O | TLSR8258 | 2.4G | 12 | 0.5 | 250kbps | SMD | 11.5*18 | ZigBee3.0 | ||
| E180-DTU(ZG120-ETH) | RJ45 | - | - | - | - | - | - | 84*82*25 | ZigBee3.0 | ||
| E180-Z6907A | 1.27mm Stamp hole | TLSR8269 | 2405M~2480M | 7 | 0.13 | 250kbps | SMD | 11.5*22 | ZigBee3.0，Low power consumption | ||
| E180-ZG120B | Stamp hole/IPEX | EFR32 | 2.4G | 18~20 | 1.3 | 250kbps | SMD | 11.5*18 | ZigBee3.0 | ||
| E180-DTU(ZG120-485) | RS485 | - | - | - | - | - | - | 66*66*21 | ZigBee ad hoc network | ||
| E180-DTU(ZG120-232) | RS232 | - | - | - | - | - | - | 66*66*21 | ZigBee ad hoc network | ||
| E180-ZG120A | I/O | EFR32 | 2.4G | 20 | 1.0 | 250kbps | SMD | 17.5 * 28.7 | ZigBee3.0 |
