[IC]：TLSR8258
[Frequency]：2.40~2.48GHz
[Power]：12dBm
[Distance]：500m
[Size]：11.5*18mm
[Introduction]：E180-Z5812SX is a ZIGBEE module designed and produced by Chengdu Ebyte based on the TELINK TLSR8258 wireless SOC. It has a small size, low power consumption, high reliability, and works in the 2.4GHz frequency band. The chip comes with a 32-bit high-performance MCU up to 48Mhz.
| Main parameter | Description | Remark |
Ideal communication distance | 500m | Two module in a sight of line, the test antenna is 5dbi antenna at 5meters. (Zigbee network supports routing multi-hop function, which can extend the transmission distance by adding routers) |
| weight | 0.9g | - |
| supporting agreement | Zigbee 3.0 | - |
| Module Type | SMD | - |
| Interface method | 1.27mm | Stamp Hole |
| IC full name | TLSR8258F512ET32 | - |
| FLASH | 512KB | - |
| RAM | 64KB | - |
| Kernel | 32 位 MCU | - |
| Dimensions | 11.5*18mm | - |
| Antenna interface | IPEX | Equivalent impedance is about 50Ω |
| Main parameter | Min. | Typ. | Max. | Unit | Remark |
| Working voltage | 1.9 | 3.3 | 3.6 | V | ≥3.3V can guarantee output power |
| Communication level | - | 3.3 | - | V | Using 5V TTL is risky to burn |
| Working temperature | -40 | - | +85 | ℃ | Industrial design |
| Working frequency | 2405 | - | 2480 | MHz | Support ISM band |
| Emission current | - | 24 | - | mA | Max Current is 24mA at 12dbm |
| Receiving current | - | 9 | - | mA | - |
| Sleep current | - | 2.5 | - | μA | Periodic sleep current averages 2.5uA |
| Maximum transmit power | - | 12 | - | dBm | - |
| Air rate | - | 250k | - | bps | - |
| Pin No. | Pin Name | Input/output | Functions |
| 1 | NC | - | Reserved, directly suspended |
| 2 | GND | - | Ground wire, connected to the power reference ground |
| 3 | NC | - | Reserved, directly suspended |
| 4 | PD3(WAKE) | Input | The WAKE pin is mainly used to wake up the dormant terminal. It is high when it is powered on. When the pin is pulled low externally, the dormant terminal device will be awakened. |
| 5 | PD7(TX) | Output | Serial transmission port TX |
| 6 | PA0(RX) | Input | Serial receiving port RX |
| 7 | NC | - | Reserved, directly suspended |
| 8 | NC | - | Reserved, directly suspended |
| 9 | PD4(MODE) | Input | Working mode switching pin, when the pull-down time is greater than 500ms, the working mode is switched. |
| 10 | PA1(BAUD_R) | Input | The UART_BAUD_RESET pin is used to reset the baud rate of the device. It defaults to a high level after power-on. In any mode, the module serial port parameters will be restored to the default 115200 if the pin is pulled down for more than 1000ms. |
| 11 | PB1(ACK) | Output | The ACK pin is used to indicate the status of the last user data transmission. The pin is pulled low before the transmission is started, and the pin is pulled high after the transmission is successful. |
| 12 | PC0(GPIO0) | Input/output | GPIO input/output port 0 |
| 13 | VCC | - | Module power supply positive reference voltage, voltage range |
| 14 | GND | - | Ground wire, connected to the power reference ground |
| 15 | PB4(GPIO1) | Input/output | GPIO input/output port 1 |
| 16 | NC | - | Reserved, directly suspended |
| 17 | NC | - | Reserved, directly suspended |
| 18 | PB5(AUX) | Output | The AUX pin indicates the current working status of the device. When the pin is low, it indicates that the device is busy, and the high level indicates that the device is idle. |
| 19 | NC | - | Reserved, directly suspended |
| 20 | NC | - | Reserved, directly suspended |
| 21 | PB6(ADC1) | Input | ADC detection port 1 |
| 22 | PB7(ADC2) | Input | ADC detection port 2 |
| 23 | NC | - | Reserved, directly suspended |
| 24 | NC | - | Reserved, directly suspended |
| 25 | NC | - | Reserved, directly suspended |
| 26 | SWS | - | Reserved |
| 27 | PC2(PWM0) | Output | PWM output port 0 |
| 28 | PC3(PWM2) | Output | PWM output port 2 |
| 29 | PC4(PWM3) | Output | PWM output port 3 |
| 30 | PC1(LINK) | Output | The LINK pin indicates the current network status of the module, and the output high-level meter has been added to the network |
| 31 | NC | - | Reserved, directly suspended |
| 32 | PD2(PWM1) | Output | PWM output port 1 |
| 33 | NC | - | Reserved, directly suspended |
| 34 | NC | - | Reserved, directly suspended |
| 35 | NC | - | Reserved, directly suspended |
| 36 | GND | Input/output | Ground wire, connected to the power reference ground |
| 37 | nRESET | Input | Reset pin |
| Order online |
| 【eBay】：https://www.ebay.com |
| 【Aliexpress】：https://www.aliexpress.com |
| 【Aliexpress】：https://www.aliexpress.com |
| For batch order/customized product |
| 【Sales hotline】：+86-28-61399028 Ext.812 |
| 【E-mail】：service@cdebyte.com |
| Technical support |
| 【Submit online】：http://www.ebyte.com/en/apple-technology.aspx |
| 【E-mail】：support@cdebyte.com |
| Model | Interface | IC | Frequency Hz | Power dBm | Distance km | Air data rate | Package | Size (mm) | Feature | Manual | Sample |
|---|---|---|---|---|---|---|---|---|---|---|---|
| E180-Z8910SX | 1.27mm stamp hole | JN5189 | 2.4G | 11 | 0.5 | 250kbps | SMD | 11.5*18 | ZigBee 3.0 | ||
| E180-Z8910SP | 1.27mm stamp hole | JN5819 | 2.4G | 11 | 0.5 | 250kbps | SMD | 11.5*22.7 | ZigBee3.0 | ||
| E180-Z5812SP | I/O | TLSR8258 | 2.4G | 12 | 0.2 | 250kbps | SMD | 11.5*22 | ZigBee3.0 | ||
| E180-Z5812SX | I/O | TLSR8258 | 2.4G | 12 | 0.5 | 250kbps | SMD | 11.5*18 | ZigBee3.0 | ||
| E180-DTU(ZG120-ETH) | RJ45 | - | - | - | - | - | - | 84*82*25 | ZigBee3.0 | ||
| E180-Z6907A | 1.27mm Stamp hole | TLSR8269 | 2405M~2480M | 7 | 0.13 | 250kbps | SMD | 11.5*22 | ZigBee3.0，Low power consumption | ||
| E180-ZG120B | Stamp hole/IPEX | EFR32 | 2.4G | 18~20 | 1.3 | 250kbps | SMD | 11.5*18 | ZigBee3.0 | ||
| E180-DTU(ZG120-485) | RS485 | - | - | - | - | - | - | 66*66*21 | ZigBee ad hoc network | ||
| E180-DTU(ZG120-232) | RS232 | - | - | - | - | - | - | 66*66*21 | ZigBee ad hoc network | ||
| E180-ZG120A | I/O | EFR32 | 2.4G | 20 | 1.0 | 250kbps | SMD | 17.5 * 28.7 | ZigBee3.0 |
