[IC] ：TELINK TLSR8269
[Frequency]：2405~2480MHz
[Power]：7dBm
[Distance]：130m
[Size]：11.5*22mm
[Weight]：0.8±0.1g
[Introduction]：E180-Z6907A is a small-sized, low power consumption, high reliability, ZIGBEE module operating in the 2.4GHz frequency band based on TELINK TLSR8269 wireless SOC, which is designed and produced by Chengdu Ebyte . The chip comes with a 32-bit high-performance MCU up to 48Mhz.
| RF Parameter | Value | Remark |
| Working frequency | 2405~2480MHz | Support ISM band |
| Max Tx power | 7 dBm | - |
| Air data rate | 250kbps | - |
| Distance for reference | 130m | Between two points (ZigBee network supports routing multi hop function, and the transmission distance can be extended by increasing the router). |
| Hardware Parameter | Value | Remark |
| Size | 11.5*22 mm | - |
| Antenna | PCB | 50 ohm impedance |
| Connector | 1.27mm | Stamp hole |
| Packing | SMD | - |
| IC | TELINK TLSR8269 | - |
| Protocol | Zigbee 3.0 | - |
| FLASH | 512KB | - |
| RAM | 32KB | - |
| Core | 32-bit MCU | - |
| Electronic parameter | Min. | Typ. | Max. | Unit | Condition |
| Operating voltage | 1.9 | 3.3 | 3.6 | V | ≥3.3 V ensures output power |
| Communication level | - | 3.3 | - | V | For 5V TTL, it may be at risk of burning down |
| Working temperature | -40 | - | +85 | ℃ | Industrial design |
| TX current | - | 40 | - | mA | Instant power consumption |
| RX current | - | 35 | - | mA | - |
| Sleep current | - | 16.5 | - | μA | Software shutdown |
| Pin No. | Pin item | Pin direction | Application |
| 1 | NC | - | Reserve，floated |
| 2 | GND | - | Ground, connected to power supply reference ground |
| 3 | PD2 | Input | Reserve |
| 4 | PC4 | Input | WAKE pin is mainly used to wake up the sleeping terminal. It is high level when power is on. When the pin is pulled low externally, the sleeping terminal device will be woken up. |
| 5 | TX | Output | UARTTX pin |
| 6 | RX | Input | UART RX pin |
| 7 | NC | - | Reserve，directly suspended |
| 8 | NC | - | Reserve，directly suspended |
| 9 | PD3 | Input | Working mode switching pin. When the pull-down time is longer than 500ms, the working mode is switched. |
| 10 | PE2 | Input | UART_BAUD_RESET pin is used to reset the device baud rate. The power-on default is high level. In any mode, if this pin is pulled lower for more than 1000ms, the serial port parameters of the module will be restored to the default 115200. |
| 11 | PE0 | Output | ACK pin is used to indicate the last user data transmission status. This pin is pulled low before the transmission is started, and the pin is pulled high after the transmission is successful. |
| 12 | PE3(GPIO0) | Input/Output | GPIO input/output port 0 |
| 13 | VCC | - | Module power supply positive reference voltage, voltage range |
| 14 | GND | - | Ground, connected to power supply reference ground |
| 15 | PA1(GPIO1) | Input/Output | GPIO input/output port 1 |
| 16 | NC | - | Reserve，floated |
| 17 | NC | - | Reserve，floated |
| 18 | PA7 | Output | AUX pin indicates the current working status of the device. When the pin is low level, it indicates that the device is busy, and high level indicates that the device is idle. |
| 19 | PE1(GPIO2) | Input/Output | GPIO input/output port 2 |
| 20 | NC | - | Reserve，floated |
| 21 | PC8(ADC1) | Input | ADC detection port 1 |
| 22 | PC9(ADC2) | Input | ADC detection port 2 |
| 23 | PC10(ADC3) | Input | ADC detection port 3 |
| 24 | PC11(ADC4) | Input | ADC detection port 4 |
| 25 | NC | - | Reserve，floated |
| 26 | SWS | - | Reserve |
| 27 | PF2(PWM0) | Output | PWM output port 0 |
| 28 | PF4(PWM2) | Output | PWM output port 2 |
| 29 | PF5(PWM3) | Output | PWM output port 3 |
| 30 | PA4 | Output | LINK pin shows current network state, high level means access to network |
| 31 | NC | - | Reserve，floated |
| 32 | PF3(PWM1) | Output | PWM output port 1 |
| 33 | NC | - | Reserve，floated |
| 34 | NC | - | Reserve，floated |
| 35 | NC | - | Reserve，floated |
| 36 | GND | Input/Output | Ground, connected to power supply reference ground |
| 37 | nRESET | Input | Reset pin |
| Order online |
| 【eBay】：https://www.ebay.com/usr/cdebyte |
| 【Aliexpress】：https://www.aliexpress.com/store/2798183 |
| 【Alibaba】：https://www.alibaba.com |
| For batch order/customized product |
| 【Sales hotline】：+86-28-61399028 Ext.812 |
| 【E-mail】：service@cdebyte.com |
| Technical support |
| 【Submit online】：http://www.ebyte.com/en/apple-technology.aspx |
| 【E-mail】：support@cdebyte.com |
| Model | Interface | IC | Frequency Hz | Power dBm | Distance km | Air data rate | Package | Size (mm) | Feature | Manual | Sample |
|---|---|---|---|---|---|---|---|---|---|---|---|
| E180-Z8910SX | 1.27mm stamp hole | JN5189 | 2.4G | 11 | 0.5 | 250kbps | SMD | 11.5*18 | ZigBee 3.0 | ||
| E180-Z8910SP | 1.27mm stamp hole | JN5819 | 2.4G | 11 | 0.5 | 250kbps | SMD | 11.5*22.7 | ZigBee3.0 | ||
| E180-Z5812SP | I/O | TLSR8258 | 2.4G | 12 | 0.2 | 250kbps | SMD | 11.5*22 | ZigBee3.0 | ||
| E180-Z5812SX | I/O | TLSR8258 | 2.4G | 12 | 0.5 | 250kbps | SMD | 11.5*18 | ZigBee3.0 | ||
| E180-DTU(ZG120-ETH) | RJ45 | - | - | - | - | - | - | 84*82*25 | ZigBee3.0 | ||
| E180-Z6907A | 1.27mm Stamp hole | TLSR8269 | 2405M~2480M | 7 | 0.13 | 250kbps | SMD | 11.5*22 | ZigBee3.0，Low power consumption | ||
| E180-ZG120B | Stamp hole/IPEX | EFR32 | 2.4G | 18~20 | 1.3 | 250kbps | SMD | 11.5*18 | ZigBee3.0 | ||
| E180-DTU(ZG120-485) | RS485 | - | - | - | - | - | - | 66*66*21 | ZigBee ad hoc network | ||
| E180-DTU(ZG120-232) | RS232 | - | - | - | - | - | - | 66*66*21 | ZigBee ad hoc network | ||
| E180-ZG120A | I/O | EFR32 | 2.4G | 20 | 1.0 | 250kbps | SMD | 17.5 * 28.7 | ZigBee3.0 |
